What are the technological processes of Jiangmen kangbeite board
1. Base treatment: clean up floating sand, floating dust and foreign matters on the wall surface, and repair to ensure that the wall surface is basically flat.
2. Wall setting out: according to the layout map of the wall and the actual situation of the site, snap the grid line of the anti beta board on the wall.
3. Keel fabrication: the keel distance is 350 ~ 600mm. The main keel of 25 * 50 * 3.0 μ m square tube is selected at the joint of the dividing plate of the anti Beite plate, and the auxiliary keel in the plate is made of 25x25x2.0 aluminum alloy square tube, and the intersection of longitudinal and horizontal keel is fixed with L-shaped aluminum alloy connector. In order to facilitate construction, the vertical and horizontal keels are assembled on the ground in advance, and each assembly unit is generally no more than 6m.
4. Keel fixation: install the assembled keel unit on the wall, adjust the flatness to meet the requirements, and fix it with expansion bolt and L-shaped aluminum alloy connector (when the wall is light weight wall, pull rivet is selected), and the distance between fixed points shall not be greater than 500mm.
5. Double sided adhesive paste: because the curing time of structural adhesive is 24 hours, double-sided adhesive tape is selected for temporary fixation. Remove the one-sided film covering of double-sided adhesive tape, and paste it on the longitudinal and horizontal keel at a distance of 150-200 mm with a length of 25 mm.
6. Injection of structural adhesive: inject structural adhesive on the surface of aluminum alloy keel, the thickness is slightly higher than that of double-sided adhesive tape, generally no less than 5mm. The structural adhesive should be applied evenly with the same thickness.
7. Paste the anti beta board: remove the film on the other side of the double-sided adhesive tape, cut the anti beta board according to the layout map, and gently press it on the keel. The gap width between plates is determined according to the decoration planning. A small amount of flatness error can be adjusted by the thickness of structural adhesive.
8. Glue injection for plate joint: paste anti fouling face print paper along both sides of the board joint, and apply neutral sealant at the plate joint with glue gun. The sealant should be embedded tightly and smooth.
9. Finishing: remove the mask paper at the seam and clean the surface.
10. Inspection: according to national standards and relevant planning requirements.
Source: Jiangmen kangbeite board http://www.jm-feifan.com/
-
10-12
How to purchase new environmental protection decorative board in Jiangmen
1. Blockboard: good moisture-proof effect, can not be directly painted. The middle of blockboard is a core made of wood strips, and the veneer is very thin on both sides, which is one of the most important materials in decoration. It can be used for furniture, wooden door and door pocket, heating cover, curtain box, etc., with good waterproof performance. In the selection, look at its internal wood, not too broken, wood gap between about 3mm Blockboard is appropriate. Because the surface exposed
-
10-12
What kinds of wall decorative panels do Jiangmen have
Experienced decoration or home decoration market has a certain understanding of friends, may know the existence of decoration board. Decoration board is a kind of primary material used in the manufacture of various finished furniture and customized furniture. It plays an important role in the decoration of the living environment and provides great convenience for the living room. General decoration board for manual manufacturing, so can better design the role of customers like, so, whether it is
-
10-12
How to deal with the internal and external corners of Jiangmen kangbeite board
Presumably, we know very little about the treatment of internal and external corners of kangbeite wallboard. Today, our Xiaobian of Jiangmen kangbeite board talks about the treatment methods of internal and external corners of wall panels. The treatment methods of internal and external corners play a connecting role in the whole process of hanging wall panels. Different treatment methods will bring different effects. Generally speaking, there are several ways to deal with the internal and extern
-
10-12
Purchasing skills of Jiangmen kangbeite board
1. When choosing the veneer degree of the anti beta board, we can distinguish it by judging the external sticker of the anti beta board. Be able to scratch the surface of the brick with a hard object. If there is a scratch, it indicates the lack of melamine paper. Compared with the melamine paper on the surface of the anti beta board, after polishing, the board will be slightly dirty, difficult to finish, and short of safety. And some of the pasted anti bate board, usually should not be laid in